Repairs to upvc window repair Windows

uPVC windows are an excellent choice for modern homes. They are easy to maintain and are durable and long-lasting. In contrast to aluminium and timber, they do not get rusty or decay.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will help prevent costly repairs and improve energy efficiency.

1. Broken Glass

If the glass in your window is broken it could cause a large deal of damage to your home, making it very hazardous and possibly fatal. It is crucial to take the time to make sure that you're doing all you can to ensure that your windows are in good repair.

Single-pane windows are relatively simple to replace and will usually fit into the frames that were previously in use very easily. If you have double-paned windows which are held together by internal beading, it will be harder to remove and replace the panes that were previously in use. In this case you'll need locate some plastic spacers that will help the new pane to fit correctly into the frame of the window.

Wearing eye protection and thick gloves is essential for anyone who plans to remove the glass by yourself. It is also a good idea to lay down a dropcloth before you begin working on the glass to ensure that any fragments of glass fall onto the fabric rather than on the floor where they can be trampled upon and cause further damage.

Once the glass is removed from the window, it's best to cover the gap with some clear packaging tape or duct tape to stop water and drafts from getting into the home until a professional is able to come out and repair the window. It also acts as a barrier, deterring any intruders from getting access into your home. If the gap is large, you might want to consider using an alarm door that comes with an integrated window repair as this will offer the best of both worlds.

2. Sagging

upvc window repair is a long-lasting and energy efficient alternative to timber sash windows. In time, they could be affected by a variety of issues such as sagging. A window that is sagging can cause problems with light, draughts, and even security. It's important to take action when you notice your uPVC windows are sagging.

Repositioning the hinges can aid in fixing a window that is sagging. First, you'll need to open the windows so you can access the frame. Then, you can remove the top and bottom hinges with a screwdriver and adjust the hinges clockwise or counter-clockwise. Close your window to test the fit after you've repositioned your hinges. If you are happy with the size of the window, tighten the screws to secure them in place.

If you are unable to reposition the hinges, you may need to replace the seal. Over time, rubber seals lose their elasticity and become dry, which causes them to lose tightness. It is important to replace your seal as soon as you can in order to ensure that your uPVC window watertight and draughtproof.

UPVC handles can also loosen. Most often, this is caused by screws that have become loose over time. However, it can also happen because the handle mechanism has worn out. Luckily, it's not difficult to repair the handle of a window that is loose yourself. First, you'll need close the window and perform an initial test to ensure that it fits. The corners of the sash should align with the casing joint. If it doesn't then you can use the screwdriver to loosen the handle. Then turn the mechanism into position.

3. Water Leaks

It is crucial to take action if you awake each day to discover mouldy walls and floors that are wet. Water leaks from windows not only lead to the destruction of your home's structure but also hamper your efforts to regulate the temperature inside your home. Most often, uPVC window leaks are caused by a damaged or missing sealant.

This is a simple fix that can be accomplished by any DIYer who is competent. Based on the severity of the problem the caulking that was used up might need to be removed before a new layer of caulk can be put on. It is essential to remember that when it comes to uPVC window repairs, you should not be tempted to apply too much caulk in order to make the area more difficult to clean and could reduce your energy efficiency.

Check that any drainage holes are free of debris inside them and ensure that the sill pan has been properly angled to allow the water to drain from the window. In more serious cases, you may need to replace the window.

Mold spots and rotted sills are other signs of water leakage. This fungus thrives under humid conditions and can propagate quickly throughout the home.

If the leakage occurs between the double-glazed glass it is more likely the problem is with the seal rather than the frame. Again this can easily be repaired by a uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or slack and open in a breeze, it may be the hinges that are at fault. They can be easily repaired by any DIYer who is skilled and are usually completed in a matter of minutes.

Like any mechanical part, hinges can be damaged over time. It's easy to change a window hinge, but it's easier if someone else helps you hold the frame.

It is also important to ensure that the uPVC hinges are opened and closed in the correct direction. This can be done by looking for the arrow on each hinge, this indicates the direction in which the window should open.

The problem with the hinges on windows could be the result of incorrectly opening the window a certain manner or because of inadequate installation at the factory. It is usually possible to fix the issue by sending us a picture through our website and we will be happy to give you suggestions.

It is also essential to ensure that the hinges are lubricated on a regular basis. This can be accomplished by applying a light engineering oil on the hinges, we recommend using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regular lubrication can help the window open and close more easily. It also decreases the possibility of a window sticking and help prevent corrosion. This is recommended to be done at least once a year. WD40 and other solvent-based lubricants are not recommended as they can damage your uPVC windows.

5. Draughts

Draughts in windows made of upvc can be caused by a few different things. The hinges can also become unbalanced due to wear, causing gaps between the frame and sash. If they're beyond repair, it may be necessary to have them realigned. The interlock may be unbalanced. This is located on the hinge side and may need to be cleaned. In some cases it might be necessary to replace the hinges.

These seals are susceptible to wear and tear or get damaged over time, allowing air to escape. This can be avoided by replacing them with high-quality weatherstripping. Replace the upvc windows with low-emissivity lenses. This will help regulate indoor temperatures and lessen draughts.

Lastly, one of the most effective ways to reduce draughts is by using an draught excluder. These are typically made of fabric filled with some kind of filler. They can be placed on the top of your windowsill. They can help keep cold air out and keep your home warm and cozy!

With a bit of regular maintenance and repairs windows made of upvc will provide a great level of security and insulation for your home. However, it is important to realize that all windows have a lifespan and they may reach the point when it's more efficient to replace them than fix them. So, if you're experiencing problems with your upvc windows, it is always recommended to seek help from a professional as soon as possible.